Technical parameters:

Laser power: 40W

Power supply voltage:AC220 10% /AC110 10% 50Hz

Weight: 20kg

:800500x250 (mm)

Maximum carving area: 200300 (mm)

Maximum inscribed area: 200100 (mm)

Working environment temperature:5 -35

Engraving speed: 10mm/s

Laser engraved chapter mechanism:

1, carbon dioxide laser

 

2, laser power

3, control panel (including power switch, laser switch test switch, lighting switch, current regulation, current display and other functions)

4, flat table (including the fixture, clip on the seal material)

5, the optical system (by the lens block and the plane mirror structure)

6, cooling system

7, smoke exhaust system

Application range:

Non metal seal engraving; such as horns and India, wood print, red plastic printing, organic glass seal, atomic seal, crystal printing, jade India

A small area of the II handicraft processing, such as in the double color plate, wood, bamboo, organic glass plate, cloth, and so on engraving a variety of graphics and text, illustrations and vivid.

The electronic components, such as the name, model, logo, design, etc.

Laser engraved chapter machine:

1, power use: one end of the 220V power supply, the other end of the machine.

2, fan installation: the exhaust fan installed in the back of the machine card slot, and then connected to the exhaust pipe.

3, water pump installation: water pump received from the back of the machine (a tie) of a pipe. And then put the pump into the bucket with pure water, the pump power plug 220V power, the water cycle (in the laser engraving machine power test, must ensure that the water cycle).

4, USB line: one end connected with the laser engraving machine, the other end connected to the computer.

5, install the dongle: first the dongle installed to the back of the computer, U disk socket.

6, software installation: open the CD, install the "laser engraved chapter machine software" folder in the software.

7, the software installation is finished: the layout operation (see the layout Manual: square, round, chapter, etc.).

8, power on test: laser engraving machine, the car will automatically detect, back to the right corner.

9, current regulation: to ensure that the water cycle of the case, press and hold the test switch, the clockwise adjustment potentiometer, the current increase; counter clockwise adjustment potentiometer, the current decreases. Current is generally transferred between 8-10.

10, positioning methods: chapter material and fixture parallel, the chapter folder in the upper right corner, the software point of "carving out", and then enter the "horizontal coordinates: 100; vertical coordinates: 20", point "position preview", the specific standard position according to each computer, adjust their own. Note: "engraving speed: 5" "interval: 2"

Laser engraving machine using the attention:

1 before starting to screw to loosen the fixing beam!

2 before starting Tonghao water, so as not to damage the laser tube.

3. Before starting to pick up line, gong wire wire end connection machine right angle, one end of the welding in spike. Spike driven into the ground, or in the water pipe above), which can protect the machine.

4 machine to be placed in a ventilated place, the circuit board is most afraid of moisture.

5 if you do not use the machine in the thunderstorm season, the power cable, data cable to pull out, in order to prevent lightning.

6 in case of software or computer system failure caused by machine running is blocked, to quickly turn off the machine power.

The material and manufacturing process of the root seal are different, different seal has different methods of keeping:

Yellow wood, horn for natural seal materials, the best seal synthetic put together, so as not to expose the excessive contraction caused by crack damage or deformation, affect the print quality.

Rubber, organic seal is made of synthetic materials, to prevent corrosion and broken.

Atomic seal, photosensitive seal to careful not to add different chemical properties of different ink, lest cause changes in the seal body properties and damage the seal.

Return ink seal in the use of the need to pay attention to force evenly, so as not to damage the seal holder.

Because all of the ink formulation different, to make cannot be mixed use, so photosensitive seal can only add photosensitive ink, atomic seal it is best to add the same brand of atomic stamp pad ink, otherwise, may be because of different seal stamp pad ink composition is not the same and the seal hardening or deformation or corrosion.

Laser engraving machine used in the introduction

Dear customer:

Hello

First of all thank you for the purchase of the company's laser engraving machine! The laser engraving machine adopts imported original device, equipped with computer automatic control system and laser technology, and has the advantages of simple operation, high speed, large depth, durable, automatic positioning, font specification, security ability and so on. The engraving machine is a precision instrument and equipment, and the transportation of the equipment is usually a railway or car transportation. In the course of transportation, it is a severe vibration that can avoid the damage or even fall off of some parts of the machine. To this end, you need to use the product before the need to check the key parts and even change one by one. Please believe that the company's technical staff are professional skills training, after a rigorous selection, they are fully equipped with the product quality status of the product quality status. The company's technical staff of the above work is entirely normal debugging, is the company's quality assurance system in the customer's extension, rather than the quality of the product, for this, especially to you.

Special tips:

1, the northern winter, in the machine idle or night rest, please the laser of circulating water discharge clean to prevent pipe water freezes and cracking laser tube. (the room temperature is relatively high, can not be considered).

2, in the carving process if it is found that the laser is getting weaker and weaker (and normal engraving depth is markedly different), if the service life of the laser is not to have may be circulating water supply is normal, please immediately shut off the power supply of the laser engraving machine, half an hour later to check whether the normal flow of circulating water, or high temperature of laser tube encounter cold water will burst, responsibility. The company is not responsible for such failure.

3, note: laser, reflective lenses for the wearing of consumables.

The quality of products is related to the quality of the device itself, and it is related to the operation skills and maintenance methods of the users. I hope you will share our skills in the operation and maintenance of the product with our technical staff during the training period!

I wish you a good business in Xinglong

Laser engraving machine installation manual

One, the main components

The laser engraving machine power supply for AC220V/50HZ if the local voltage instability, please install 50

 

4、Install the exhaust tube head into the air outlet of the fan, the exhaust fan is inserted into the slot will be on the right hand side of the body (Figure) 

 

5、Connected to the fan, cooling water pump, engraving machine power, and take good.

 

6、

Start the pump to cool the water cycle, start the exhaust fan, the laser engraving machine switch, this time the laser engraving machine should be self check and automatic reset.

7, the power of the laser engraving machine, the end of the USB cable connected to the laser engraving machine motherboard USB interface, the other end of the computer USB port

8, the installation of computer software (specific steps, please refer to the software specification)

Two, the use of instructions

1, operation panel description

Power switch: used to start or close the laser engraving machine

Current indicator: used to indicate the current size of the engraving machine

Current regulation: use this potentiometer to adjust the size of the current when it is based on the current indicator

Lighting switch: used to start or shut down the light in the laser engraving machine (a number of machines without this switch).

Laser switch: used to control whether the laser light, in the engraving seal when the switch is connected to the state (that is, press)

Test switch: this switch is pressed when the laser is shining, at this time according to the current meter display data adjust potentiometer to adjust the current size of the sculpture. This switch is only used to debug the machine and check the current size, when the machine is working correctly, the computer will automatically control the engraving.

2, use, should start the cooling water pump, and then start the laser engraving machine, and to ensure that the cooling water cycle.

3, start carving system typesetting software, designed the carved image, good engraving position, (specific steps, please see the specification of the software) carved chapter material fixed to the fixture and the material plane and the plane of the fixture in a plane, can engrave output (should pay attention to is engraved rubber material fashion to a small piece of newspaper into the water immersion, tiled in material, engraved chapter to a brush into the water and gently rubbed in the newspaper. As shown in figure.

4, the current adjustment should be based on different seal black and process requirements to adjust the size of the current.

Three, note

1, laser engraving machine should be placed on the desktop, not tilt

2, laser engraving machine to prevent a strong vibration, when the mobile should be fixed to the car and the car, in order to prevent vibration caused by light path or laser beam.

3, the exhaust pipe should be connected to the outside of the room, and to maintain good ventilation, often wipe the fan and the machine inside the machine

4, laser engraving machine has high voltage, non professional and technical personnel shall not open the case for maintenance, in order to prevent electric shock.

5, laser engraving machine if it is the first time to use or move the location, pay attention to check whether the high voltage line is off, to prevent electric shock.

6, laser engraving machine exhaust fan, cooling water pump is AC220V/50HZ power

7, engraving machine ground must be a good grounding

8, laser engraving machine work must prevent staff or other personnel hand or eyes to see, to prevent laser wounding or injury to the eye, it is best to cover buckle dead.

9, please avoid the equipment inside the water or working environment is too wet. The machine should be placed in a dry ventilated place.

10, strictly charged removing various connectors.

11, engraving machine lens should use anhydrous ethanol or acetone to clean in time, and to wipe gently, Cawan after adjustment of light road.

Light path adjustment see part of the description

12. To ensure the cooling water circulation is good and clean water, such as the yellow water dirty should change the water in a timely manner, so as to avoid the laser tube cooling is not good to burst.

13, pay attention to prevent because of the icy water cooling, the weather is very cold in the North should pay special attention to the winter is the best for automotive antifreeze, the temperature is too high, the scale or dirt clogging mechanical impact and other reasons caused by laser damage.

14, pay attention to prevent corrosion and damage caused by dust inside the chassis parts due to excessive humidity. So after each workpiece to clean the machine, to keep the machine clean, to do the ground wipe.

Four, fault and exclusion

1, engraving seal output laser head is not action

The determination of the laser engraving machine is even state machine;

- check print cable is off;

- print port lock solution can be caused, laser engraving machine and computer are closed, and then restart your computer;

- check the carving board 24VDC indicator light is bright, if not bright, no motherboard power supply 24VCD power

2, no laser engraving

Laser switch - check on the operation panel is pressed;

The current inspection on the operation panel adjustment knob is in the lowest position;

] check the cooling circulating water is working properly; (for the sake of safety, it is recommended users to contact the manufacturers or distributors around the agent, need a professional technical staff to adjust, is also available in training during training).

- check the light is normal;

Whether due to damage or the life of laser tube;

(the selection of the original plant of the laser to be replaced with the laser power to match, to ensure that the engraving effect and the use of laser life)

Fault - laser power supply board, please replace the laser power supply.

(proposed to buy the original laser power for replacement)

3, when the image is normal, but the effect is not good

- check the engraving plane and the focus is coincidence;

- check the light is normal;

The laser tube is aging;

The plotter is badly worn.

4, the car and the car to walk when abnormal sound

The street is too wet to check whether the optical component failure.

The optical switch connector on the board or bad light contact is not good;

The optical switch sheet deflection or shedding.

-

Choose stone laser engraving machine stable and reliable product quality, after sale service guarantee! We promise that every user has stone engraving machine to buy peace of mind, with the worry, after sale service that allows you to rest assured! Company website: http://www.mslaser.cn, http://www.moshidiaoke.com, http://www.diaokejiqi.com

Contact phone: 0635-8705351 15063591363 18906358552

QQ: 380862605 907777911582049764

      380862605